top of page
BIF Services Resin Flooring floor coating photo

Industrial Resin Floor Coatings provide a fast, economical answer for areas needing a tough, dust-free floor finish.

You may have tried a floor paint, but BIF install the latest, most advanced resin floor coatings which provide significantly better performance.

 

Achieving a durable surface starts by choosing the most suitable type of coating and the most effective method of floor preparation.

 

We include concrete repair as part of our scope, so if your floor shows signs of cracking, wear or damage, our team will stabilise the surface before any resin is applied so that your new floor finish takes daily use  for  years to come.

Resin Floor Coatings 

Tough & Cost Effective Floor Treatments

Waterbased Epoxy Coating

200 micron Dry Film Thickness

BIF Services Resin Flooring EP Coat WB 3D

Applied in two coats, these 2-component coatings provide excellent penetration and adhesion and offer excellent abrasion resistance.

 

Typical areas of use;

 

  • Warehousing & Storage

  • Light Industrial Units

  • Plant Rooms

  • Service Corridors

  • Light Engineering

  • Manufacturing Environments

  • Vehicle Body Shops

  • Inspection Bays

 

BIF - EP - Coat WB

Our two-part, water-based coloured epoxy coatings provide an entry point to advanced industrial floor coatings systems.

 

Floor paint comes in many forms, but our two-part water-based epoxy coatings deliver fantastic durability and are incredibly hard wearing when used in the right environments and particularly suited to new build projects.

 

Water-based industrial floor coatings are water-miscible, which means they can be applied on freshly poured concrete surfaces, without the  expense of a DPM Primer, or waiting for the concrete to dry sufficiently. These coatings allow dampness to breath from new concrete.

 

Offering outstanding durability with foot traffic, a correctly applied coating will support hygiene and prevent dust proliferation, often seen in areas with bare concrete surfaces.

BIF provide full mechanical surface preparation, removing laitence and all other surface contamination. Very large areas can be prepared and installed within just a couple of days, meaning low cost installations are possible on larger areas of 1000m2+.

BIF provide a 12 month warranty on this type of industrial floor coating.

 

 

Slip

Resistant

High Load Resistance

Chemical Resistance

Easy

Clean

Scratch Resistant

UV

Resistant

Seamless Hygiene

Colour Range

BIF Services Resin Flooring DCLC floor coating photo
BIF Services Resin Flooring safety aisle coating photo
BIF Services Resin Flooring corridor photo
BIF Services Resin Flooring floor coatings photo
BIF Services Resin Flooring BIF-EP-HB Coating 3D

Installed as a 2 or 3 coat system (with optional DPM Primer), these tough floor coatings provide a high gloss sheen and are commonly used in areas such as;

 

  • Busy Warehouse & Storage areas

  • Plant Rooms

  • Aircraft Hangars

  • Mechanical Workshops

  • Distribution Centres

  • Light Engineering & Manufacturing Environments

 

 

BIF - EP - Coat HB

 

High Build Coatings are the next step up from water-based coatings, providing additional durability and a thicker, smoother surface layer.

 

They're also solvent free, allowing installation whilst production continues in adjacent areas. Where slip resistance may be an issue High Build Coatings can be installed with an added fine aggregate to increase under foot traction.

 

These systems need a dry substrate, with a maximum 75%RH. Readings taken above these levels should require either a surface chemical DPM Primer, or use of a water-based epoxy (see above), however BIF will provide advice on suitability.

 

 

Slip

Resistant

Scratch Resistant

High Load Resistance

UV

Resistant

Chemical Resistance

Seamless Hygiene

Easy

Clean

High Build Epoxy Coating

500 micron Dry Film Thickness

Colour Range

scampton floor coatings photo
BIF Services Resin Flooring DCLC 2020
BIF Services Resin Flooring coatings photo
BIF Services Resin Flooring BIF-EP-Flow 3d

From High Build Coatings, thicker systems are available with a choice of; 

BIF-P-Flex (a flexible polyurethane resin finish),

BIF-EP-Flow (a rigid epoxy 2mm thick finish)  

BIF-EP-Grip Eco (which adds slip resistance) all provide additional durability and a thicker, smoother surface layer.

Increasing the thickness of the floor finish chosen may  also improve the flatness of a floor, but we will engineer your existing floor (if cracked, uneven, worn or corroded) and would suggest you see our Engineered Surfaces page which shows how we can flatten and repair most surfaces before installing a suitable floor finish.

 

We will provide options to reduce cost as part of our service.

 

 

The next step...

Are you looking for durable safety line markings?
bottom of page