HydroCoat 107 Elastic 2K Waterproof Tanking Membrane for the Protection of Below Ground Structures
Cementitious coating for the waterproofing and protection of concrete and masonry. Can be spray-applied so ideal for large projects. Suited to the waterproofing of reservoirs, tunnels, water tanks, basements, podium decks, flat roofs and balconies.
Features and benefits:
- Pre-packaged materials easily mixed on site.
- Tough, flexible coating which maintains its elastomeric properties even under immersed conditions to accommodate movement in cracks.
- Good abrasion and very high resistance to freeze/ thaw cycles and de-icing salts.
- Excellent adhesion to sound prepared concrete and masonry substrates, as well as steel.
- Dense matrix offers low permeability to water, even at 10 bar pressure, and very high diffusion resistance to carbon dioxide gas.
- Suitable for positive and negative waterproofing of earth-retaining structures as well as covered decks.
- A 2 mm coat provides the equivalent to 135 mm of good quality concrete cover.
- Can be applied to damp substrates in temperatures down to 5°C.
- Water-based product, free from hazardous solvents, ideal for use in confined spaces. Non-toxic when cured.
- Correctly prepared suitable substrates include concrete of at least 20 kN, steel, masonry and screed.
- Can be applied via squeegee, roller, airless spray, pin leveller, brush or trowel.
- CE marked and manufactured in accordance with EN 1504-2: 2004.
- Guaranteed to resist weathering for up to ten years.
Other Products and Services from Newton Waterproofing
Crystalline Waterproofing of Concrete Newton HydroCoat 104 Super
HydroCoat 104 is applied to the surface of concrete to provide in-depth protection against the movement of moisture through the capillaries and hairline cracks within the concrete. It consists of Portland cement, specially treated quartz sand and a compound of active chemicals. HydroCoat 104 is supplied in powdered form and is either sprinkled onto fresh concrete or is mixed with water as a carrier and brush or spray applied as slurry for application to fully cured or older concrete or vertical surfaces.
The active chemicals combine with the free lime and moisture present within the capillaries to form insoluble crystalline complexes which effectively block the capillaries and any minor shrinkage cracks to prevent any further movement of moisture to provide a totally dry surface to the concrete.
Large areas can be quickly treated with HydroCoat 104. The speed of application and the low material application rate (1 kg/m²) makes this product a very low-cost option for various scenarios.
Because HydroCoat 104 penetrates deep into the concrete, it does not leave a physical membrane to the surface of the concrete element and so is completely unaffected by loadings imposed by further elements of the build. New concrete elements are placed ‘concrete to concrete’ with no potential for slip or separation as is the case with physical membranes.
Features and benefits:
- Single component.
- Ease of application − sprinkled onto new concrete and applied as a simple slurry to vertical and cured concrete. Permeates deep into the concrete to form a barrier against moisture that cannot be damaged or punctured.
- Loading capabilities only limited by the strength of the concrete.
- No physical membrane − subsequent concrete placement is ‘concrete to concrete’.
HydroBond 2K-Flex Primer
A fast-drying bitumen emulsion primer and bonding agent that is applied to the substrate prior to the application of the Newton HydroBond 2K-Flex reinforced bitumen waterproof coating. The product adheres well to concrete, masonry, plaster and most other common construction substrates.
Rubber Waterproofing Membrane Newton HydroBond 109-LM
Radon-certified, flexible, single-component, cold-applied and seamless rubber waterproofing membrane used primarily for the external waterproofing of earth-retaining structures such as basements and foundation walls.
HydroBond 109-LM is extremely puncture resistant with elasticity of 850% and a 95% recovery memory. The membrane becomes fully engaged into the substrate to prevent water tracking and is suitable for all below ground and earth-retained structures, ranging from domestic basements to the largest civil engineering projects.
HydroBond 109-LM is available in two variants: Medium Viscosity, for use in warmer temperatures, and Low Viscosity, for when it is cooler. HydroBond 109-LM is also a constituent product of the Newton HydroBond System supported by BDA Agrement Certificate BAB 16-031/04/A and is accepted by the NHBC as a suitable waterproofing system for Type A Waterproofing to Grades 1a, 1b, 2 & 3 - BS 8102:2022.
Newton Waterproofing
Unit 17-19, Sovereign Way, Tonbridge, Kent, TN9 1RH, United Kingdom
Newton Waterproofing Systems, est 1848, is the UK's leading independent supplier of structural waterproofing systems, including cellar and basement waterproofing, tanking and pumping products, damp proofing, water control and drainage products.