FSDCDS - Sanitary Rupture Discs

The CONCOA 304 Series is a three-port, chrome-plated brass, single-stage point-of-use regulator designed for high-purity, non-corrosive, or liquefied gases (up to grade 5.5). It provides secondary or final-line pressure control, reducing delivery pressure in a single step. Its durable construction and high-purity compatibility make it a cost-effective solution for applications that can tolerate minor outlet pressure fluctuations as cylinder supply decreases. Maximum inlet pressure is 3000 PSIG (210 BAR) or higher, depending on configuration.

Features:

• 316L stainless steel diaphragm prevents inboard diffusion

• CAPSULE® seat with 360° integral filtration

• Low wetted surface area reduces purge requirements

• Rear panel mount simplifies installation

• Helium leak-tested for integrity

Specifications:

• Max inlet pressure: 3000 PSIG (210 BAR)

• Body: Chrome-plated brass barstock; Bonnet: Chrome-plated die-cast zinc

• Gauges: 2" (50 mm) plated case

• Seat: PTFE; Filter: 10-micron sintered bronze

• Temperature range: -40°F to 140°F (-40°C to 60°C)

• Cv: 0.1; Diaphragm: 316L stainless steel

• Helium leak integrity: 1 × 10⁻⁸ scc/sec

• Internal seals: PTFE; Ports: 1/4" FNPT

• Compliance: Meets/exceeds CGA G-4.1, PED 2014/68/EU, ANSI/ASME B40.1, CRN OH5216

The Kunkle Bailey 716ESL Safety Relief Valve (featuring an EDPM disc and Lifting Lever, designed for use with water and gas services, but not suitable for air) is a highly efficient safety relief valve. It boasts a top-guided, unobstructed seat bore with full lift capability, ensuring maximum discharge performance. The Bailey 716 safety relief valve is certified to BS6759 parts 1, 2, and 3, making it ideal for safeguarding vessels, pipelines, and equipment that handle hot or cold water, air, steam, as well as various gases and liquids.

Specifications

Sizes: Ranging from 1/2" x 3/4" up to 2" x 3"
Connections: BSP Female Inlet x BSP Female Outlet
Materials: Bronze body, Chrome Vanadium spring
Disc: EDPM
Medium: Suitable for gases and liquids, including air and hot water
Set Pressure: Varies from 0.35 to 32 Barg (dependent on size)
Temperature Range: -29 to +150 °C (maximum)

Note: This product is also known as IMI Bailey Birkett valves, Kunkle Emerson valves, and Safety Systems UK valves.

For optimal safety and performance, consider the Kunkle Bailey 716ESL Safety Relief Valve for your industrial applications.

The PREL100023 High Capacity Sealed Heating System Pressure Relief Valve discharges water off the system at a set pressure in the event of system over pressurisation (high for larger capacity systems) Reliance Valves 100 Series Pressure Relief Valves are made from hot pressed brass and are predominantly used to protect closed-circuit wet heating systems from overpressure. The outlet is one size larger than the inlet to ensure high discharge flow rates. It has a separate seal seating from the diaphragm to give improved scaling resistance and a cover which is made from OT58 brass. Available in a variety of sizes to suit most installations, it also has a pressure range from 2.5 - 5.0 bar, with the response pressure indicated on the twist cap. The valve size is determined by the heat output of the boiler as shown in the maximum heating capacity table. 

Features and benefits: 

- High flow design for larger capacity systems 

- Outlet is one size larger than the inlet for high capacity discharge 

- Provides protection against over pressurisation in wet heating systems 

- Diaphragm design gives improved resistance against scale 

- Cartridge design gives ease of service and replacement without the need to reset the response pressure 

- Set pressure range from 2.5 - 5.0 bar to suit any system requirement 

- High lift design for increased discharge capacity 

- Suitable for heating applications only 

Specification

Size: 1" x 1.1/4"Connections: BSP Female Inlet x BSP Female OutletMaterials: Hot pressed DZR BrassMedium: WaterSet Pressure: 3 BargTemperature: +140 degCProduct Code: PREL100023Notes: WRAS approved